What Are you Running on your ride

[69Mach1man]

What are you running on your ride?
include a pic it you can

[69Mach1man]

I have a 1969 mach1 mustang
351W with a 408 stroker kit :eek:
hooker super comp headers
edelbrock 800cfm carb
edelbrock RPM air Gap manifold
CrainCams Gold Alluminum RollerRockers
Luanti Custom Ground Cam
MSD 6al ignition
MSD Pro-Billet Distributor
Aeromotive Street Rod Fuel Pump
Aeromotive Billet Fuel Pump Controller
March alluminum pulleys
3"x3" Dr. Gas Exhaust Crossover Kit
Edelbrock 304 series mufflers with turndowns


http://www.imagestation.com/picture/sraid52/p93e0c74153cd2bf0d776b68a6c43125f/fc946832.jpg
http://www.imagestation.com/picture/sraid52/p5622fe3f92a7325067cd8cd81d93345c/fc946831.jpg
http://www.imagestation.com/picture/sraid53/p3efdeaeb09b9dc13aabbb57cec52e3ec/fc941619.jpg

[johnc1996]

96 cobra

tremec 3550, ram 900series, alum driveshaft, alum billet flywheel
4.10s built rear end with 31 spline mosers
mac ceramic coated long tubes, mac prochamber
msd dis-4 ignition box
accel coil packs
u/d pullies
anderson power pipe
125 wet shot
stock heads cleaned up a little

solid motor mounts
upr tubular chromoly k member and a arms
front and rear adjustable coil overs
lakewood 90/10s and 50/50
adjustable lower control arms
welded tq boxes
chromoly solid uppers
steeda subframes
battery relocated to trunk optima red top

[AbecX]

Originally posted by 98gtmustang
stock heads cleaned up a little
:rolleyes:

[Monsoon X]

Forged 383 short block. Too small of a cam for a stroker motor and stock LS1 heads. What can I say? It's a work in progress!

[302_plus_a_few]

302 with bolt ons - lots of bolt ons.

[Kris]

306 on ephedrine.;)

[The Raven]

Forged and blown H/C/I 284, the little motor that could.;)

[Ylw 98~~SNAKE~~]

4.6 DOHC 3.73 offroad H flows K&N and bottle baby mod

[Andrew]

302 with an strim.

[Dolomite]

258 with flipped air cleaner lid and stuck rings.

[nmra310]

Long rod 306
ross pistons 10.5:1
victor jr. heads
victor jr intake
holly 750
3.73s
3550
driveshaft
full drag suspention
tubular k-member
built rearend

1991 coupe..

oh yea and aloto juice:D

[StangTamer]

The fastest car on this board and its a Pontiac.

[redfiveohconv]

64.5 mustang coupe

Single plane Holley high rise
750cfm 4bbl man. choke Street Demon
Crane cam/1.6 rockers
2 Chamber Flows
4.10s

Many parts waiting for installation-friendly weather. ;)

[93LXHORSE]

A bunch of parts scattered across several garages, but they are orbiting close and closer together and shall soon be as one.

[TexasDevilDog]

A little 280CID four valve engine.

[Wario]

I drive a slow ass pos 4.6 2V bolt-on junker:(

[46Tbird]

2.5 liters of fury backed by a 5-speed and 3.73s.

http://www.dfwstangs.net/hosting/46Tbird/Ranger2.jpg

[mikeb]

462 pontiac street motor with a little bitty cam. That's it.

[NDSP]

www.i-systemsmedical.com/BigBlock.htm

[black on black coupe]

Stock 5.0 :(

[98DSM]

4 Banger :D and some other goodies.

[blaze1076]

Piece of shit 2002 GT- 281, piece of shit welded in flows, piece of shit MAC prochamber, piece of shit diablo chip, piece of shit 70mm TB, and three piece of shit steeda pullies.:D

[AbecX]

Custom Ross forged pistons, with eagle 3D Hbeams, some eagle forged crank, ported heads, decent intake, 28oz balanced assembly going through a 5spd and 3.08 gears in a mostly stock rear end. Couple of suspension things and new windshield wipers.

http://dfwstangs.net/hosting/AbecX/dsc00003.jpghttp://dfwstangs.net/hosting/AbecX/smallsig.jpg

[Milo]

357ci,efi,t trim,c4.

[Bubb Rubb]

Early model Ford Probe, 18" Chrome Enkie's, dual whistle tips.

[Monsoon X]

Originally posted by AbecX
Custom Ross forged pistons, with eagle 3D Hbeams, some eagle forged crank, ported heads, decent intake, 28oz balanced assembly going through a 5spd and 3.08 gears in a mostly stock rear end. Couple of suspension things and new windshield wipers.



SLOW

[AbecX]

Originally posted by Monsoon X
SLOW
Only when you ride with me.

[Monsoon X]

Originally posted by AbecX
Only when you ride with me.

Why? Because I weigh 200lbs?

[AbecX]

Originally posted by Monsoon X
Why? Because I weigh 200lbs?
I have to pop my sun roof to get your head to fit, the drag slows me down. Do I have to explain everything to you now?

[Monsoon X]

Originally posted by AbecX
I have to pop my sun roof to get your head to fit, the drag slows me down. Do I have to explain everything to you now?

It's not my ego it's your lack of self-confidence! :)

[AbecX]

Originally posted by Monsoon X
It's not my ego it's your lack of self-confidence! :)
:rolleyes: Punk, I'm not Back n' Black, I'm abecx, stop getting us white trash confused :mad:

[Hicompression]

Check it out....

[ThreeFingerPete]

stock 305.
88 Trans Am

adam

[GTek]

Originally posted by Dolomite
258 with flipped air cleaner lid and stuck rings.


:D :D :D
That brought back some old high school memories.

[4DRSS]

Originally posted by StangTamer
The fastest car on this board and its a Pontiac.

LOL!

[4DRSS]

I'm running a stock bottm end LT1 with ported stock heads and a BIG hyd. cam. I have a nitrous kit sitting in the garage waiting to be installed.

[redfiveohconv]

You dug in deep to get this one 4DRSS.

[66Deuce]

N/A 350.

[SonicBlueCoupe]

2002 GT with stock suspension, and after Saturday it will have:

Steeda UD pullies
Ignition Solutions Plasma Booster
9'' K&N conical filter
85mm C&L mass air
100mm Desncharger air tube
98 Cobra single bore Accufab TB
P&P bullitt intake
P&P 2002 PI heads
w/ Mod Max oversize valves
Mod Max springs
Bronze valve guides
Comp Cams XE270AH cam
BBK longtube headers
Mac prohamber
Mac Pro Dumps

Still needs gears and suspension. Should put out over 300 rwhp, not bad for a little 4.6L 2V.

[32VfromHell]

Originally posted by 69Mach1man
I have a 1969 mach1 mustang
351W with a 408 stroker kit :eek:
hooker super comp headers
edelbrock 800cfm carb
edelbrock RPM air Gap manifold
CrainCams Gold Alluminum RollerRockers
Luanti Custom Ground Cam
MSD 6al ignition
MSD Pro-Billet Distributor
Aeromotive Street Rod Fuel Pump
Aeromotive Billet Fuel Pump Controller
March alluminum pulleys
3"x3" Dr. Gas Exhaust Crossover Kit
Edelbrock 304 series mufflers with turndowns


http://www.imagestation.com/picture/sraid52/p93e0c74153cd2bf0d776b68a6c43125f/fc946832.jpg
http://www.imagestation.com/picture/sraid52/p5622fe3f92a7325067cd8cd81d93345c/fc946831.jpg
http://www.imagestation.com/picture/sraid53/p3efdeaeb09b9dc13aabbb57cec52e3ec/fc941619.jpg

do you have heads on it? or stock heads? put a set of AFRs on it, or TW-Rs!

[GRAYHORSE]

Originally posted by SonicBlueCoupe
2002 GT with stock suspension, and after Saturday it will have:

Steeda UD pullies
Ignition Solutions Plasma Booster
9'' K&N conical filter
85mm C&L mass air
100mm Desncharger air tube
98 Cobra single bore Accufab TB
P&P bullitt intake
P&P 2002 PI heads
w/ Mod Max oversize valves
Mod Max springs
Bronze valve guides
Comp Cams XE270AH cam
BBK longtube headers
Mac prohamber
Mac Pro Dumps

Still needs gears and suspension. Should put out over 300 rwhp, not bad for a little 4.6L 2V.

Sounds similar to mine, let me know if you make it over 300rwhp. Thats what im shooting for. What size injectors and is the bottom still stock? Greg

[MustangJohn]

:D

[SSMAN]

350 with all old school man! But I have the Holley Sytemax package to go on it along with a 750 Barry Grant Silver Claw or a Holley 750 pro series, I haven't made up my mind. I have both. B&M 400 Tranny, 3000 rpm stall. Oh....an a 12 bolt with 3:73's


Oh an a neat little temp gauge for the intake.:D

[SonicBlueCoupe]

Originally posted by BLACK96STROKER
Sounds similar to mine, let me know if you make it over 300rwhp. Thats what im shooting for. What size injectors and is the bottom still stock? Greg

30# injectors, and its still the stock bottom end. I am starting the install of the heads/intake/cams Friday, hopefully I'll have it dyno tuned later this month or early next.

[Red92Stang]

93 LX Coupe

a lot of these parts are being installed right now or were just installed

306 w/ forged internals
GT-40 upper and lower w/ spacer
Edelbrock Performer heads w/ 1.9/1.6 valves
E-303 Cam
1.6 RRs
65mm Throttle Body
75mm Mass Air
42 lb injectors
JMS chip
built AOD
3200 Stall
Texas Turbo Longtube Headers
custom 2-cat h-pipe
Edelbrock cat-back
Vortech S-Trim w/ 10# pulley
T-rex inline fuel pump
190 in tank fuel pump
aluminum driveshaft
Lakewood 90/10s
Lakewood 50/50s
subframe connectors
Eibach Drag Launch kit
HPM megabite Jr's
31 spline Strange axels
full spool
drag radials
probably some other stuff i left out

when i get it back im gonna break in the motor and take it to Speedworks, i hope to make around 510+ rwhp

[Cooter]

Originally posted by BBRANJEN
750 Barry Grant Silver Claw or a Holley 750 pro series

go with the HP!!!!!!!!!!!

[mean90]

98 gt, o/r h flows, stock 3.27 gears, ram air, ud pullies, and a 100 dry shot. 9.3 at 75 on motor and hopefully low 8's with 100 shot:cool:

[Josh]

All in the parts in the sig plus full front and rear tubular suspension, 6pt roll cage, fuel system and more.

http://www.mustang50magazine.com/50mustangsuperford/featuredvehicles/p131470_image_large.jpg

[Strychnine]

383 with not enough cam ;)

Pic links are in the sig.

-Matt

[GRAYHORSE]

Originally posted by SonicBlueCoupe
30# injectors, and its still the stock bottom end. I am starting the install of the heads/intake/cams Friday, hopefully I'll have it dyno tuned later this month or early next.

haha, I'm starting to put mine back together Sat. Can wait to see our numbers. I also have 30#, but i have built bottom end. Hope it last this time. Greg

[J-MAN]

382W
victor jr. heads and intake
950 hp
kooks headers
solid roller
3 1/2" ultra flows
C4
8.8 w4.10's

I guess that's it

[11secCobra]

sonic blue 03 cobra

o/r x pipe, pro dump flowmasters, and a 95mmC&L